SKYSTARS F722 APP WIFI HD3 Flight Controller BLHELI_32 KM60 60A 4in1 ESC 3-6S DSHOT600 Fly Stack

$105.00

What makes this FC different from others?

1. Solder pads are the largest in size compared to other FC in market.
2. Proper solder pad spacing to avoid solder bridge and facilitate easy soldering.
3. ESC connector on top-side rather than bottom which makes it easy for repair.
4. Support ELRS receiver row pin straight mounting.
5. TVS Diode for Reverse Polarity Protection and Voltage Spike Suppression.
6. Powerful BEC to supply all your electronics.
7. Pads arrangement are executed in such a way that when you twist the wires of the camera VTX and RX you don’t get any wire overlapping this gives you a uniform twist and clean look.
8. DJI connector on the top side.
9. Budget-friendly price ( We understand the situation of chip shortage and rising prices of FC )
10. Two stages of Quality check to reduce any faulty electronic.
11. No power lines near Gyro to avoid any EMI interference.
12. Comes ready with I2C support and INAV.

Category:

FC Specifications:

MCU: STM32F722RGT6 216MHz
Gyroscope: BMI270
Baro:Bmp280
OSD: Betaflight SPI OSD DJI HD OSD(UART6)
Black box: 16MB
6x Uarts: UART 1/2/3/4/5/6
4x PWM outputs
1x I2C
3x LEDs for FC STATUS(blue)and 3.3V indicator(Red)
USB Type-C(USB2.0)

1x JST-SH1.0_8pin connector (Gnd/Vbat/S1/S2/S3/S4/Rx3/Curr)

1x JST-SH1.0_6pin connector (R1/G/R6/T6/G/10V)

VTX 10V/Vbat filtered power ON/OFF switch

DJI FPV OSD is supported by any spare UART

LED: 4 LED independent pads, support WS2812 programming lamp output.

Receiver: Support Sbus, crsf, ibus, SBUS, XBUS, support 3.3v Spektrum satellite receiver, The default receiver input is UART1(You can solder ELRS RX on UART1), F7 has a built-in inverter, which can actually be installed in any spare UART.

Power:

Input voltage: 3-6S
BEC: 5V/10V 3A max dual-channel BEC supports stable power supply on the sky side of DJI
LDO 3.3V: Max.250mA

FC Firmware:

WIFI: SpeedyBee APP target name SKYSTARS F7
BetaFlight firmware: SKYSTARSF722Pro
INAV firmware:SKYSTARSF722HD

Mounting:

Installation size: 30.5mm × 30.5mm The installation hole is M4 and supports shock column installation
External size 39mm × 39mm
Flight control weight: 6.9g
Flight control onboard voltage sensor.

KM60A 4IN1 3-6S ESC BLheli32 DShot1200 4-in-1 ESC:
Support Dshot1200, Dshot600, Dshot300, Dshot150, Oneshot125, Multishot, PWM control signal

Power supply voltage: 3-6S (12-26V)
Continuous working current: 60A
No built-in 5V BEC output
Firmware: BLHELI 32 ESC
Screw hole spacing: 30.5*30.5MM
Aperture: 4MM
Weight: 14.6g

– The ESC has an on-board filter capacitor that suppresses the back electromotive force, stabilizes the battery voltage, and protects the flight control ESC precision components.
– EMI Shell provides stronger anti-interference capability.

Including

1x F7 Wifi HD Pro FC
1x KM60 BL32 4IN1 ESC
8x Silicon grommets M4 to M3
2x JST-SH1.0_8pin cable, 4cm
1x JST-GH-6P cable for DJI port, 10cm

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.

Scroll to top